Yamaha Raider Blaster-X Tail Light Retrofit Kit (Circuit Board Only) for the Yamaha Road Star Warrior 02-09 and the all NEW 08-09 Raider and Raider S models. High Performance LED Tail Light Retrofit Integrator Kit.
- Features our Microprocessor based Blaster-X Technology with Brake Alert and Strobe Mode built in!
- Installs into OEM housing (assembly required).
- All electrical connectors and detailed instructions provided.
- Recommended accessory: ELFR-1 Flasher Relay
- Made in the USA!
- 2-year Warranty!
This is an integrated LED tail light retrofit for the stock 2008 - 2009 Yamaha Raider and Raider S tail light. All the internals of the stock tail light unit are replaced with a ultra high-tech Custom LED circuit board containing 32 Ultra Bright Red LEDs and 32 Ultra Bright Yellow LEDs - compared to only 16 red LEDs on the stock circuit board!
FEATURES:
- 32 Ultra Bright Red LEDs for running and brake lights.
- 32 Ultra Bright Yellow LEDs for turn signals.
- Custom LED ColorChange Technology on-board.
- Custom LED Blaster-X PWM technology on-board.
- Custom LED Strobe Mode!
- Custom LED Brake Alert!
- New Programming Interface allows users to easily customize features!
- New Sure-Blink Technology
- Robust regulated design for consistent and reliable performance.
- 4 MHz microprocessor controlled operation.
- Detailed step by step instructions with illustrations for a simple install.
- Smart color matched wires matches motorcycle wires for easy wiring.
- Only 3 wires to hook up outside of tail light housing.
- All electrical connectors and hardware provided with kit (does not include outside switch for functions)
- NOT DOT approved.
This product features our proprietary and patented Blaster-X, Brake Alert and Strobe Mode! With this product, your turn signals are built right into the tail light! It's the best fender eliminator money can buy.
Brake Alert automatically provides a few quick ultra-bright strobe pulses of light the instant the brakes are applied. This alerts motorists the instant you apply the brakes - possibly saving seconds of reaction time for non alert motorists! The number of pulses can be user-configured VIA our new Programming Interface! It can also be disabled if desired.
Strobe Mode is a feature that puts the taillight into a devastating strobe cycle that is sure to get anyone's attention. This mode produces insanely bright pulses of light at ultra high frequencies, in alternating patterns across the tail light. Strobe mode is engaged by grounding a control wire, and can be engaged at any time.
Blaster-X is our proprietary pulse-width-modulation technology that squeezes the maximum possible illumination power out of LEDs. The result is a significantly less expensive, yet even more outstanding and effective product than it's predecessors - and widens our advantage over our competitors.
NEW! This product also marks the introduction of our NEW Programming Interface which allows users to easily customize features of the tail light! The customizable features menu allows users to:
- Enable or Disable the Startup Sequence.
- Set the number of pulses in the Brake Alert feature (can set to zero to disable Brake Alert).
- Adjust the running light brightness within a preset range.
- Adjust the brake light brightness within a preset range.
- Engage Demo Mode, where the tail light cycles through all functions automatically and repeatedly!
- Reset factory defaults.
This programming interface is accessed very simply through the Strobe Mode control wire! The interface is designed to receive input simply by providing ground pulses to the strobe mode control wire. No special equipment is necessary to access and utilize the programming interface! Detailed programming instructions will ship with every unit.
NEW! And last but not least, our Sure-Blink Technology. Our Integrated Tail Lights are designed to follow the turn signal commands of the motorcycles flasher relay. This insures it is compatible with all after market and OEM flasher relays - especially programmable relays such as our ELFR-P. However, in the event that the tail light receives a command to blink that does not break (blink) within a preset time period, the tail light will automatically blink that side. This feature is most useful in preventing common no-blink problems that are associated with retrofitting motorcycles to LEDs.
Just as on the other Custom LED integrated LED tail light models, the system is designed so that the red LEDs turn off (on one side) when the yellow LEDs come on, so that the turn indication is a pure and distinct yellow light. The unit automatically flashes between the red and yellow on the side you're turning! The Yellow LEDs are slightly offset as well, creating a dramatic attention grabbing effect.
The engineering is solid and dependable, the looks are unbeatable, and the brightness is incredible! Don't waste your time with half hearted solutions, do it the right way from the start, with Custom LED.
Custom LED Circuit Boards are IN STOCK, McCoy Motorsports will no longer offers installations for Custom LED Integrated Tail Light circuit boards. The boards come with pictured step by step instructions and if you need any help with installation just give us a call and one of friendly customer service representatives will be happy to talk you through the installation.Thanks for understanding and we appreciate your business!
