Introducing the Custom LED ELFR-P Programmable Electronic Flasher Relay! This micro controller based, plug and play flasher relay has 10 preprogrammed user selectable flash patterns! The flash pattern is easily selected by a 10 position rotary switch conveniently located on the compact unit.
Click here to see the working video (note: In video new pattern changes every 10 seconds).
This flasher relay system will operate properly and consistently for blinker loads ranging from 0.1A to 5A, which basically covers any combination of any blinker products on the market!
The fuse protected 18" long harness allows for plug and play* operation for motorcycles listed in our computability list below. For motorcycles not on the list, the unit may be hard wired to any motorcycle with a two wire flasher relay, or three wire flasher relay system where the third wire is a ground. The extra long length allows for convenient mounting of the flasher relay, for easy access during flash pattern selection.
Each flash pattern was optimized for effectiveness when used with ANY type of blinker indicators such as: LED blinkers, stock blinkers, incandescent blinkers or integrated LED tail lights! There are several different flash patterns ranging from DOT (stock) blink patterns to super intense strobing patterns to slow fading patterns. You can be sure to find a pattern that suits your taste!
* in addition to the direct plug and play connector, a single ground wire with affixed loop connector must be connected to the negative battery terminal. *
FLASHER RELAY COMPATIBILITY LIST:
Yamaha: YZF-R1, YZF-R6, YZF600, FZ-1, FJR1300
Honda: CBR1000RR, RC-51, CBR600F4i, CB919, ST1300, GL1500, CBR1100XX, CBR900RR, CBR929RR, CBR600F2, CBR600F3, CBR600F4, VTR1000R Super Hawk, VT600, 02-04 1800 C, 02-03 1800 R models, 02-03 1800 S models, 04-05 1300 C models, 03-05 1300 S models, 05 1300 R models
Kawasaki: ZX-10R, ZX-12R, ZX-6R(R) up to 04, Z-1000, ZXR1200(1100), ZZR1200, ZX1200, ZR-7
Suzuki: All late model GSXR's with two-wire replaceable flasher relays are also compatible, but require a hard-wire installation.
Ducati: 996 - hard wire installation as follows when replacing OEM relay with our Electronic LED Flasher Relay:
- Motorcycle Light Blue (LB) gets connected to the ELFR-X Red wire
- Motorcycle Pink (P) gets connected to the ELFR-X Black wire
- Motorcycle Black is not used.
Yamaha: Roadstar line, V-Star - hard wire installation as follows when replacing OEM relay with our Electronic LED Flasher Relay:
- Motorcycle Brown wire to ELFR-X Red wire
- Motorcycle Brown/white stripe wire to ELFR-X Black wire
HARD WIRE INSTALLATION INSTRUCTIONS: if your existing flasher relay is a two wire flasher relay (or a three wire with a ground wire), and you have access to it, you can replace it with our flasher relay as follows:
- Red wire on ELFR-X to power source (ignition switched +12V)
- Black wire on ELFR-X to load (blinker lamps/ blinker switch)
And MANY more! Although we try to keep this list current and complete, there are many more bikes out there that are Plug -and-Play compatible, and hard wire compatible with our LED Flasher Relay. We can not list them all! If your motorcycle has a two wire flasher relay, our relay will work for certain but may need to be hard wired into the harness. For three wire flasher relays, if one of the three wires is merely a ground wire, our relay will work but may need to be hard wired into the harness.
IMPORTANT NOTE: Your motorcycle MUST have a replaceable two wire flasher relay to use this product. A few motorcycles have flasher relays which can not be replaced due to the fact that they are integrated into other electronics. Most flasher relays are located under the seat or behind the headlights. Please review your repair manual, or consult an expert as to whether your motorcycles flasher relay is replaceable.
